Marcelo Costa info on Airlink+ ASOHO-4P:

--------------8<--------------------8<-----------------8<----

Hit any key for boot setup
## Starting application at 0xffcb0000 ...
UART initialized
start = ffc00000, vid = 20, did = 225bQD initiated
ethPortInit OK...
num of Vids = 2
interacfe 0, header=030, vid=2
00:40:f4:87:38:cd
Attach interface unit=0
FD_Iit().. Done701a0, basRxDesctr = 07014a0
               Ope interace unt=0
Attach interfce uni=1vid=1
Openinterfce uni=1
MV6218_IfIoctl() set ifnet address
netJobAdd fail
MV6218_IfIoctl() add/del m'cast addr
MV6218_IfIoctl() set ifnet address
netJobAdd fail
MV6218_IfIoctl() add/del m'cast addr
2








                            NetMall System Boot


Copyright 2002  ADMtek, Inc.



CPU: ADM   0 Home Gateway Processor
POST Version: 2.00.0032
Creation Date: 2003.06.25


Press <space> key three times to stop auto-boot...
0

Verifying product code......PASS
Boot Product Code!!!
UART initialized
start = ffc00000, vid = 20, did = 225bQD initiated
ethPortInit OK...
num of Vids = 2
interacfe 0, header=030, vid=2
00:40:f4:87:38:cd
Attach interface unit=0
FD_Iit().. Done70140, basRxDesctr = 07014a0
               Ope interace unt=0
Attach interace unt=1 vid=
Ope interace unt=1
MV6218_IfIoctl() set ifnet address
MV6218_IfIoctl() add/del m'cast addr

DHCPS:DHCP Server Started.
MV6218_IfIoctl() add/del m'cast addr

==========================================================================
  Triphibian project:
    Command Line Interface. v.2.00.0028 2003.06.26
==========================================================================

cmd> Block address ffce0000, block_end = ffcf0000, end = ffce449e
write ffce449e size bb62write ffce0000 size 449dBlock address ffce0000,
block_ee
write ffce0000 size 8000write ffcec49e size 3b62write ffce8000 size 449d

==========================================================================
  Triphibian project:
    Command Line Interface. v.2.00.0028 2003.06.26
==========================================================================

cmd>    help

            Command Line Interface v0.01
======================================================
rmem      : Read memory.
        Usage : rmem <Address> [Num of Words]
wmem      : Write memory.
        Usage : wmem <Address> <Data0> [Data1] ... [Data7]
rhword    : Read memory (Half-Word).
        Usage : rhword <Address> [Num of Words]
whword    : Write memory (Half-Word).
        Usage : whword <Address> <Data0> [Data1] ... [Data7]
rmi       : read mii phy register.
        Usage : rmi <phy addr> <reg>
wmi       : write mii phy register.
        Usage : wmi <phy addr> <reg> <Data>
time      : Get current system time.
        Usage : time
settime   : Set system time.
        Usage : settime <hh:mm:ss> [yy/mm/dd] [TZ(GMT ± hour)]
help      : List all commands.
        Usage : help
mkdir     : Make directories.
        Usage : mkdir <dir>
create    : Create files.
        Usage : create <file>
cat       : Concatenate files.
        Usage : cat <file>
ls        : List directory contents.
        Usage : ls [dir]
rm        : Remove files.
        Usage : rm <file>
rmdir     : Remove directories.
        Usage : rmdir <DIRECTORY>
copy      : Copy files.
        Usage : copy <source> <destination>
nvclear   : Clear all of the NVFS files.
        Usage : nvclear
routeShow : Show Route.
        Usage : routeShow
mbufShow  : Show Mbuf statistics.
        Usage : mbufShow
ifShow    : Dispaly network interface.
        Usage : ifShow <ifname>
ifAllShow : Dispaly all network interface.
        Usage : ifAllShow
taskShow  : Show Task informations.
        Usage : taskShow
semShow   : Show Semaphore informations.
        Usage : semShow
timerShow : Show Timer informations.
        Usage : timerShow
memShow   : Show memory pool informations.
        Usage : memShow
msgqShow  : Show message queue informations.
        Usage : msgqShow
eventShow : Show event group informations.
        Usage : eventShow
knlShow   : Show kernel resource informations.
        Usage : knlShow
ipConfig  : Configure interface address and subnet mask.
        Usage : ipConfig [ifname] [ip] [subnet mask]
ipStatus  : Change IP status. 1 for Enabled, 2 for Disabled..
        Usage : ipStatus [ifname] [status]
ipAdd     : Add alias IP address..
        Usage : ipAdd [ifname] [ip] [netmask]
ipDel     : Delete alias IP address..
        Usage : ipAdd [ifname] [ip] [netmask]
arpAdd    : Add an ARP entry to ARP table..
        Usage : arpAdd [ip] <Ethernet Address>
arpDel    : Delete an ARP entry..
        Usage : arpDel [ip]
arpGet    : Get the hardware address of a specify IP..
        Usage : arpGet [ip]
arpFlush  : Flush ARP table..
        Usage : arpFlush [ifname]
ping      : Ping a host..
        Usage : ping [ip] [ms]
dhcpcRelease: Release the IP address for the specified interface..
        Usage : dhcpcRelease [ifname]
dhcpcRenew: Renew the IP address for the specified interface..
        Usage : dhcpcRenew [ifname]
dhcpcLog  : Show dhcpclog..
        Usage : dhcpcLog
dhcpcLogTest: Test dhcpclog..
        Usage : dhcpcLogTest [line_num]
dhcpsStart: Start DHCP Server..
        Usage : dhcpsStart
dhcpsStop : Stop DHCP Server..
        Usage : dhcpsStop
dhcpsAddIp: Add static IP to the DHCP server.
        Usage : dhcpsAddIp [mac(00-00-00-00-00-00)]
[ip(xxx.xxx.xxx.xxx)]
dhcpsDelIp: Delete static IP from the DHCP server.
        Usage : dhcpsDelIp [ip(xxx.xxx.xxx.xxx)]
dhcpsBindingNum: Print binding number of the DHCP server.
        Usage : dhcpsBindingNum
dhcpsShowStatic: Print static IP of the DHCP server.
        Usage : dhcpsShowStatic
natShow   : Show NAT link table information.
        Usage : natShow
triggerPort: Set trigger port, when public port num is 0 will delete
this entry.
        Usage : triggerPort [index] [port] <protocol> [public port num]
[start].
triggerShow: Show trigger port information.
        Usage : triggerShow
gethostbyname: gethostbyname.
        Usage : gethostbyname
tftpc     : TFTP client.
        Usage : tftpc <GET|PUT> <host> <remotename> <localname>
tftps     : Start TFTP server.
        Usage : tftps [dir] [timeout]
update    : Update runtime code (need to download image file "download"
to /tmp.
        Usage : update
setAccessHost: Add/delete access host.
        Usage : setAccessHost [NET(xx.xx.xx.xx)] [MASK (xx.xx.xx.xx)]
<index>
accessHostShow: Show access host information.
        Usage : accessHostShow
ripStart  : Enable RIP .
        Usage : ripStart [version]
ripStop   : Disable RIP .
        Usage : ripStop
ripShow   : Show RIP table .
        Usage : ripShow
wlanchan  : Get/Set Channel .
        Usage : wlanchan [chan]
wlanssid  : Get/Set SSID.
        Usage : wlanssid [ssid]
wlanwep   : Get/Set Wlan WEP .
        Usage : wlanwep [wep]
wlansts   : Get Wlan Statistics .
        Usage : wlansts
arW       : AR Ram Write .
        Usage : arW IO_Base Ram_Addr Bytes
arR       : AR Ram Write .
        Usage : arR IO_Base Ram_Addr Bytes

--------------8<--------------------8<-----------------8<----

and this is when I hit enter at boot

--------------8<--------------------8<-----------------8<----
Hit any key for boot setup


ARMboot Rev 1.42 for RD-88E6208 C (May  6 2003 - 14:18:40)

  _----_     ____
 | ---- |___/  __)___
 |      |       _____)
 |      |       ______)
 |      \__    ______)
 |       \_\________)
 |         ---,
/___/\_._._._./

ARMboot LE version
ARMboot code: 00380000 -> 0038b300
ARMboot->
ARMboot-> help
go      - start application at address 'addr'
loadx   - load binary file over serial line (xmodem mode)
md      - memory display
mm      - memory modify (auto-incrementing)
nm      - memory modify (constant address)
mw      - memory write (fill)
cmp     - memory compare
printenv- print environment variables
setenv  - set environment variables
saveenv - save environment variables to persistent storage
defaultenv- get default environment variables
fburn - write a block to the FLASH memory
bdinfo  - print Board Info structure
reset   - Perform RESET of the CPU
echo    - echo args to console
version - print monitor version
help    - print online help
?       - alias for 'help'

ARMboot-> printenv
bootdelay=3
baudrate=38400
ethaddr=08:00:3e:26:0a:5b
ipaddr=010.002.050.127
serverip=010.002.002.050
netmask=255.255.000.000
bootfile=bootrom.bin
sdramImgAddr=0x00100000
flashAddr=0xFFC00000
bootSource=flash

Environment size: 208/4092 bytes

ARMboot-> version

ARMboot Rev 1.42 for RD-88E6208 C (May  6 2003 - 14:18:40)
ARMboot-> bdinfo
enetaddr      = 00:00:00:00:00:00
baudrate      = 38400 bps
arch_number   = 0
env_t         = 00000000
boot_params   = 00000000
DRAM:00.start = 00000000
DRAM:00.size  = 00800000
boot flash base   = FFC00000
boot flash size   = 00200000

--------------8<--------------------8<-----------------8<----